Finding and restoring old amps and cabinets is a slow process that demands patience. From the time we first began trolling eBay, ultimately scoring a tweed Vibrolux and Tremolux, to final delivery of the aged cabinets and assembly of the amps, six months had easily passed.
We first found and bid on a ’58 Vibrolux in September ’06. Sold by an eBay seller in Texas, it had been recovered in reddish-brown cloth similar to the stuff used to cover hymnals or a bad ’60s pleather recliner for the double-wide. Otherwise, it was pretty straight, with the original blown Jensen P10R intact, and the original transformers, caps and resistors. The inside of the cabinet had been painted black, but the cabinet, grill cloth, baffle and control panel were otherwise intact, and the wooden tremolo footswitch was included. We bought the Vibrolux for $1,590.00 with 4 bids placed.
Inspired by Larry Cragg’s detailed description of Neil Young’s tweed Tremolux, a1958 Tremolux surfaced on eBay in November 2006, and we scored it for just $1,082.00 from a seller in San Francisco. We suppose this amp was so cheap because the output transformer had been replaced, and the cabinet had been completely stripped and stained mahogany brown. The original speaker mounting screws in the baffle board were about to fall out. However, the original Tremolux circuit was well-preserved, and a small strip of tape remained in the chassis signed in a delicate hand by “Lilly” – one of the many women in Fullerton employed to assemble amplifiers like the Tremoluxin 1958. God bless her. The Tremolux also arrived with the original wooden foot switch.
The Vibrolux kicked some serious tail right out of the box. We send the original Jensen P10R to John Harrison at A Brown Soun (www.abrown.com) for a re cone, mounting a1965 Jensen C10Q sent by Larry Pogreba in its place – a very stout choice and original equipment in early blackface Vibrolux Reverb amps. Like the Tremolux, the tremolo circuit in the Vibrolux required some TLC,with four caps needing replacement to restore the swampy oscillator circuit to full wobble-weave. We also replaced all the newish tubes with NOS RCAs, Philips and GEs. Once we had the amp mounted in the restored and aged cabinet, we were throwing down hard with our No caster nightly, wallowing in the big sound coming from such an innocent-looking little biter, when the original output trans-former gave it up in a final, glorious gasp. A quick call to Mercury Magnetics produced a ToneClone replacement within a week and we were soon back in business,sounding better than ever.
The 10 watt, 3-input ’58 5F11 Vibrolux is housed in the same cabinet Fender used for narrow panel tweed Deluxe– a fat little featherweight with greasy tremolo and a smooth bark tailor made for a Telecaster. And 10 watts may be the perfect power notch for low-volume home recording and jamming – crystal clear, bright and drenched in gorgeous Fendery overtones at low volume (3-5), and absolutely on fire from 7-10. In all respects, the 5F11 Vibrolux is a big amp in a small package worth pursuing for its outstanding tone and personality at truly usable volume levels.
We were amazed by how Gregg had managed to remove every trace of black paint that had been sprayed inside the cabinet, and his aging job, complete with three coats of amber stain and lacquer, faint water stains along the bottom,worn seams and corners, aged L&L leather handles and scorch marks from the power tubes on the inside of the back panel were flawlessly conceived and applied. Hopkins even recreated the original tube chart with a 1958 date code after requesting that we send him the chassis number and power transformer EIA code for production verification. When we brought the restored Vibrolux to Jeff Bakos’ shop (www.bakosampworks.com), he looked it up and down as it sat on the floor of his workshop, peered into the back and said, “That is totally sick.”
The ’58 Tremolux provided a further study in what can be involved buying 40 year-old amps. Upon arrival,the amp was really smokin,’ even with the Jensen hangin’ off the baffle board. The tremolo was DOA, however, so while the stripped cabinet was getting the spa treatment in St. Louis, Jeff replaced two caps in the trem circuit, we replaced the already replaced output transformer with another from Mercury Magnetics, and stored the chassis away until we received the finished, aged Tremolux cabinet from Gregg in late March ’07.
The 5E9A (’55-’56) and 5G9 (’57-’60) Tremolux are housed in the same taller, wider cabinet Fender used for the 1×15 narrow panel tweed Pro,and the later 5G9 circuit is quite different from both the 5E3 Deluxe and the ’55 5E9ATremolux, being fixed rather than cathode biased, employing a long-tailed phase inverter common to the bigger narrow panel tweed amps, and the addition of an extra filter cap and choke enabled the power to be increased from 15W to 18W in 1957.
Compared to the narrow panel tweed Deluxe and the 5E9 Tremolux, the 5G9 Tremolux develops more volume and headroom, and should you chose to replace the 12AY7 preamp tube with a 12AX7, gain is further increased (it’s already righteous with the 12AY), while the bigger 10” x22” x 10” cabinet produces a much rounder, warmer tone with superior ambience and presence. In the month or so since we’ve had the Tremolux put together in the restored cabinet, a new Tung Sol6V6 blew (after we had opted not to use a couple of spare ’50s RCAs for safety – they are in the amp now and killin’ us with bogs of good thang),and we just took the amp back to Jeff when it began spitting some nasty distortion provoked by low frequencies from the guitar. Turned out to be a few bad solder joints.
Like the Vibrolux, Gregg had stopped short of creating a “3-legged dog with an eye patch,” taking the aging to a moderate level with frayed edges and seams on the amber tweed, a single beer can ring on the top with a foam overflow stain running down the grill cloth, a slight orange stain on one side from pine knot bleed, and assorted scuffs and light abrasions. He also repaired the baffle-board, filling in the old holes for the speaker mounting screws.
We hate doing this to you (again), but truth be told, we have to give the nod to the Tremolux as the most toneful and inspiring amp in its power class (18 watts)that we have ever heard or owned. It’s ascension to Numero Uno status was a bit of a surprise, but then again, we considered the initial source of our inspiration for finding one – Neil Young, via his tech, Larry Cragg, and in hindsight we should have expected as much. With all the attention paid to the tweed Deluxe as the big time bonerizer of the tweed family, the Tremolux seems to have been overlooked for the usual reasons…. In the nose-to-butt-crack daisy-chain march to mediocrity, the masses never seem to acquire a view beyond the first lazy dumb-ass directly in front of them. In the immortal words of the great hoosier educator and smack-down artist Earl Dosey, they are “stepping’ over dimes to pick up nickels.” Let’s hope the lemmings continue to keep their heads down.
So here’s the move…. Sad as we are to share this, our strategy was as obvious as it seems. Forget about original speakers, don’t let a replaced tranny run you off (we’ve never replaced one with a Mercury that didn’t sound better than the original), and deliberately track down the fuglies told girls you can find from the tweed era. Busted baffle boards? We luv that….Ricky-ticky cabinets are good, and the coverin’ don’t matter. What you want is a beater with a totally neglected chassis and as many of the original fat Astron caps and original resist or present as possible. Yeah, some of them may have to be replaced, but it’s far better to allow a prudent and judicious amp tech determine that rather than buying an old amp that has been raped by a hard chargin’ cowboy hooked on Sprague Orange Drops.Buy one of those and your old amp will sound new,never to sound old again, and that’s most definitely not the play you want to make here. A little component drift is good.
There is luck involved, too… not all vintage amps were created equal. Some of them left the birthing bench endowed with incredible tone – a happy accident created by the melding of variable components that resulted in extraordinary sounds. Others were created by the same roll of the dice, but with a different outcome altogether – mysteriously dull, flat, or simply lacking whatever you wish to call it… that tone, mojo, bloom, the harmonic complexity of your first Schlitz, depth, fatness… whatever. To experience the blissful afterglow of unanticipated discovery, you must be willing to risk something, which is another way of saying that faith must be exercised in the absence of a guarantee. In this respect, buying old amps is a lot like life itself…. The greatest obstacle to discovery is the flawed perception of an impossible challenge. And the window of opportunity is closing on these great old amplifiers faster than you may think. Like vintage guitars, the best old amps are being taken out of circulation by col-lectors willing to pay prices that are based on potential future value (more than they are worth today, perhaps, but less than they will be worth tomorrow). For you, hombre, the time to bust a move is now.
Founded in the mid-1940s in Fullerton, California by Leo Fender, the legendary amps produced by this company have been heard on countless recordings and are influential on countless other amp makers. In the beginning Fender paired small combo amps with lap steels and electric guitars aimed at student players, but word of the superior tone and build quality quickly spread among professional musicians. In over seventy years of existence, Fender has consistently evolved and innovated its sound from the Tweed era through the Brown and Blackface eras and beyond.
Mercury Magnetics has built a massive collection of ToneClone® Transformers and Chokes for Fender Amps available from all eras of production. Answering the needs of players and amp-builders alike, our extensive catalog of audio transformers is the ultimate resource whether you’re looking to replace a worn-out transformer in a vintage Fender amp or looking to nail a vintage tone in a new amp or amp build. The engineers at Mercury have painstakingly documented every detail and nuance of the best-of-breed vintage transformers and can faithfully produce perfect clones using the same materials and methods used on the originals.
The ToneClone+ Series from Mercury Magnetics adds more utility and options without altering the original tone. Love your amp but want to change your speaker configuration? Mercury’s ToneClone+ Output Transformers give players more impedance options like alternate and multi-tapped secondaries. Power Transformers can benefit from the “Plus” treatment as well with alternate primary voltage, Higher or Lower B+ Voltages, added current capability, and more.
Fender Woodie Amp Transformers: The earliest production amps to come out of Fullerton, Fender ‘Woodie’ amps can be identified by their hardwood cabinets and fixed handles. We are proud to offer ToneClone® transformers from this short-lived and rare Woodie era including the Woodie Deluxe (aka Model 26) and Woodie Pro.
Fender Tweed Amp Transformers: The Fender Tweed era lasted from the late forties to early sixties and a vast 
amount of artists from all generations have crafted their distinct tone using these amps through all genres. Notable artists include: Scotty Moore (Elvis Presley), Neil Young, Larry Carlton, Eric Clapton and Keith Richards. Mercury Magnetics has the largest catalog of vintage-correct Fender ToneClone® replacements transformers for the following models: Tweed Bandmaster, Tweed Bassman, Tweed Champ, Tweed Harvard, Tweed Princeton, Tweed Pro/Dual Professional, Tweed Super, Tweed Tremolux, Tweed Deluxe, Tweed Twin, and Tweed Vibrolux.
Fender Blonde and Brown (Brownface) Amp Transformers: Sitting on the timeline between the Tweed and Blackface Fender amps, the Blonde/Brown amps of the early sixties were most noticeably embraced by surf groups like the Beach Boys and Dick Dale. Our catalog of ToneClone® amp transformers for this era includes Brown/Blonde Bandmaster, Blonde Bassman, Blonde Showman, Blonde Tremolux, Blonde Twin, Brown Concert, Brown Deluxe, Brown Princeton, Brown Pro, Brown Super, Brown Vibrasonic, Brown Vibrolux, and Brown Vibroverb. Also see our transformers and choke for the 6G15 Reverb Unit.
Fender Blackface Amp Transformers: Easily distinguishable by their black control plates and white lettering, Fender Blackface amps began showing up on stages and recordings in the early-mid 1960s. Extremely popular among musicians then, the impressive build quality and versatile tones have kept these classic amps popular even 50 years later. Mercury Magnetics has hundreds of ToneClone® and ToneClone+ transformers and chokes for Fender Blackface Amps including: Blackface Bandmaster/Bandmaster Reverb, Blackface Bassman, Blackface Champ, Blackface Concert, Blackface Deluxe/Deluxe Reverb, Blackface Princeton/Princeton Reverb, Blackface Pro/Pro Reverb, Blackface Showman, Blackface Tremolux, Blackface Twin Reverb, Blackface Vibrochamp, Blackface Vibrolux, and Blackface Vibroverb. Also see our transformers and choke for the 6G15 Reverb Unit.
In this issue we are dealing with a subject on which I have received many inquiries in the past. It is about the selection or matching of tube amps for the best possible Jazz sound. Amplifying acoustic or semi-hollow-body guitars has always been a huge challenge because most jazz guitarists are very demanding in terms of sound and simultaneously fight against unwanted distortion and feedback. In the following article I would like to summarize some tips and tricks that get great tone and how to avoid distortion.
When I started getting involved with jazz sounds, around 1977, most guitarists in this genre used transistor amplifiers. George Benson played a Polytone, Pat Metheny an acoustic amp with a 4×10” speaker cab and Volker Kriegel and Michael Sagmeister used a Gibson LAB L9 with 15” speakers. Such examples can be found very often from that period. Although all of these guitarists had indeed very good tone, the typical depth and openness of a tube amp sound could not be reached however in its wider spectrum. Still the transistor amps had some advantages over tube amps: They sounded very compact and linear, were less prone to feedback and offered a relatively balanced frequency spectrum and a nice sustain, which was the ideal sound of many jazz guitarists. A Gibson L5 played through a LAB or a Polytone is completely convincing – even today.
One disadvantage that the transistor amps had in particularly was its dynamic behaviour, in their relatively poor response and in their tendency to not let the individual character of a particular guitar fully unfold. You could also say: Transistor amps tend to standardise tone.
I do not wish to start a discussion about tube versus transistor because transistor amplifiers will continue to play a rightful role in jazz. It is more about ways to show how one can get the typical warm jazz tone with a tube amp without all the disadvantages.
Above all I am thinking of the sounds of the early sixties, which were marked by numerous jazz guitarists including: Wes Montgomery, Kenny Burrell, the early George Benson, Herb Ellis, Joe Pass, Barney Kessel, Grant Green and Jim Hall. All of these guitarists were playing tube amps on their early recordings and getting fantastic sounds. Today tube amps are celebrating a renaissance with jazz guitarists.
Let us first take look at the most popular models from the distant past. In the fifties the combos from Fender (Tweed), Gibson, Standel or Flot-A-Tone were especially loved by jazz musicians due to their sound and their small size. These amplifiers were sufficient for jazz guitarists because they were usually accompanying musicians and they performed as a soloist only in rare cases. They often stayed in the background and did not play very loud.
Even back then, most jazz guitars were equipped with a tone control that made it possible to filter out unwanted peaks and thus to form the typical dark jazz sound. But soon the guitar became a solo instrument. Just think of the impressive sound of a cascading Les Paul, who at that time had good reason to play on a solid body. The traditional jazz players remained with their hollow bodies and now had to fight against all the disadvantages of the electrification of their sounds. Recently I read in a retrospective of Wes Montgomery that he alleged that during his entire career he was unhappy with his sound because he simply could not find the perfect amp. One might even go so far and assume that the dark jazz sound is actually created only (and eventually cultivated) because the amount of unpleasant highs tube amplifiers have, are rather imperfect sounding and also quickly led to feedback. Most guitarists wanted more of a linear and natural reproduction of their beautiful instruments that already sounded great acoustically.
Let’s now take a look in the interior of a tube amp and consider certain circuit characteristics which can be modified for a better jazz tone. The objectives of these measures are the reduction of distortion and the high frequencies, improving the mid-range and increasing the linearity of the sound.
First, a list of known suitable amplifiers for conversion to a “jazz box”: Fender Tweed Fender amps from 1956 and Brownface, Blackface and Silverface combos. Examples from this list shall be explored in following issues.
Let’s start with a Tweed Deluxe amp replica from Cream which I have converted for jazz sounds. These amps are known for their distortion when left stock and therefore not ideal for a clear jazz tone. But they are very small and handy and with around 15 watts of power ideal for use in a club. In addition, these amplifiers are connected with a so-called “split-load” phase inverter which is appropriate for our purposes because of its low gain. The only drawback is the two coupled volume pots, which restrict the volume control range on the one hand and deliver too much gain in the preamp. The aim is to reduce the gain in the preamp and increase the output power and stability of the amplifier. Only then we get enough headroom for a clear sound.
Just this once, I should like to “put the cart before the horse” because there are a number of measures to improve the amp without intervention on the circuit.
First, these amplifiers usually have an inefficient speaker. Powerful speakers with a good efficiency rating are especially suitable for jazz sounds. Those who love the Alnico sound can search out an old JBL D-120 and replace the aluminum dust cap with a counterpart out of fabric (available from Weber VST). The speaker can be helped dramatically in the highs and we get a warmer, rounder tone. Excellent was also the old Fane Crescendo Heavy-duty speaker, which is also suitable after the removal of the aluminum dome making a perfectly clear and powerful sound. These speakers were also used by David Gilmour. Another excellent choice is also an Electro-Voice 12L or a Jensen C12K with 100 watts. All these speakers better the sound of the Tweed Deluxe significantly. You only have to watch out for the thin baffle-board because vibration during transport could for example pull heavy speakers from the screw holes.
A further stabilizing method is the conversion of the power tubes to 6L6 or 5881, which I recommended at this point several times. Although the amp has only about one or two watts more output, the increase in headroom is very clear. You get more clean reserves and dynamics. Here I recommend changing the cathode resistor of the amplifier from 250 (typically with 5 watts) to 330 ohms with 10 watts. If you play a jazz guitar with humbuckers, we recommend the low input of the normal channels. Here there are less highs and the output signal of the guitar is more attenuated. It should be noted that the volume pots affect each other on the Tweed Deluxe. By turning the unused channel by not more than 70 percent, the tone is much cleaner, but also quieter.
If you don’t wish to utilize this trick, you can simply remove the cathode of the second stage capacitor (Elko 25mF/25 volts) and reduce the gain of this stage substantially, which in turn increases headroom. The amp will be clearer and somewhat linear, but also a touch softer.
Even more clear sound can be obtained by replacing the output transformer. Something I always do in such tuning. In this case I choose a Mercury Magnetics Tweed Pro Axiom FTPRO-O transformer (available at Tonehenge Amplification) with 8 ohms, which gives much more stability to a small tweed amp.
If you want to use the amp only for jazz, you can also decouple the two volume controls from each other and only one channel and a tone control remain. Now you can adjust the volume much finer and linear. The circuit can be found at www.schematicheaven.com under Fender Deluxe 6G3. Here the channels are completely separate, each with their own volume and tone control. It’s only after the volume knobs on the channels that two 220k ohm mixing resistors are mixed together again.
Since the Tweed Deluxe played with humbuckers has in general somewhat bassy sounds, I also reduce the value of the coupling capacitors from 0.1mF to 0022mF. This makes the sound tighter and more mids. Sprague “Orange Drop” P715-type fit perfectly here.
Finally we get to fine-tuning via preamp tube placement. With a good 12AY7 and a 12AX7 of your choice, you can continue to shape your favourite tone. For those of you who have not had enough, you can play with the value of the capacitor on the tone-pot. The Deluxe was originally installed with a 0005 UF capacitor but also possible are values such as 0.01mF or 0.02mF (as in the 6G3) for a slightly warmer tone. If you want to darken the sound one can bridge one of the anode resistors at the 12AY7 with a 0.003mF capacitor (as in the normal channel of the Brown Vibrolux).
The result is a truly compelling jazz amp for small clubs, feeds back less, offers more clean reserves and could compete with any Polytone but all the benefits of dynamic and harmonically rich tube sound can be enjoyed. Diana Krall’s guitarist Anthony Wilson often used a Tweed Deluxe replica from Clark and his blond Gibson Byrdland in the studio. This sound is very reminiscent of Kenny Burrell and offers a wonderfully unique character. Have fun experimenting!
Fender designed and built more than one transitional, non reverb blackface combo amp that would soon acquire reverb and a new name, including relatively small numbers of blackface Princetons, 4×10 Concerts, 1×12 Vibrolux and 1×15 Pros. We acquired a 1×15 blackface Pro, and while it ultimately proved to be an extraordinary exceptional amp, we were also reminded of the potential pitfalls that exist when buying old amps sight-unseen, as well as the potential rewards.
We found the ’64 Pro listed on eBay and bout it from a dealer after requesting a detailed photo of the chassis and circuit. Proudly described as “the best amp in the store, “the rare ’64 blackface Pro is essentially a blackface Vibroverb without the “verb.” Do we have your attention yet? Three caps had been replaced, the original baffleboard had been professionally converted to plywood with the original grill cloth remaining intact, and an on/off pot had been installed for the tremolo intensity control that bypassed the tremolo circuit when rolled to “1” with a click, adding gain that would otherwise be missing in the Vibrato channel. We pulled the JJ power tubes and assorted Russian pre-amp tubes and replaced them with lightly used,“test new” RCAs from our stash, rebiased the amp and fired up the Pro….
Sounded like shit. We had been here before with a dead-mint ’64 Vibroverb bought years ago that had passed through a certain amp guru’s hands in Pflugerville, Texas.How could a vintage Fender sound so bad we wondered? Turned out that the value of the bright cap on the Vibrato channel had been changed on the Vibroverb, rendering a thin, scalding tone that would have given Ed Jahns fits, as it did us. Changing the bright cap back to spec immediately restored the Vibroverb to its rightful pace in history, but the Pro had other problems….
The baffleboard swap and added switch on the tremolo intensity control were clues that someone had also spent time troubleshooting the amp, probably trying to detect the cause of the Pro’s weak output, thin tone and curiously harsh edgy distortion. The amp just didn’t sound right. We pulled the original, reconed Jensen C15N dating to 1964 and subbed in an Eminence Legend, but the Pro still sounded choked-off, linear and wrong, so it was off to Jeff at Bakos Amp works on the Friday afternoon before Memorial Day weekend in a frog-chokin’ Georgia thunderstorm. When the going gets weird, the weird turn pro…..Now, this is the difference between someone who really knows his craft and a hack….Jeff plugged his bench guitar into the Pro, hit a couple of chords, issued a single grunt of displeasure and caustically observed, “Something is definitely fucked up.” With the chassis on the bench, Jeff scowled at the choppy sine wave the amp produced on his scope as he checked voltages with his multimeter. “I think the output transformer is going down slow—it measures 11 volts and it should be reading 16….” He clipped in a substitute OT from a stout old Fisher hi-fi, plugged in and hit a chord… “That’s closer to what it’s supposed to sound lie….” And sure enough, the missing lows and mids were present, the raspy treble tones were subdued, and for the moment, the Pro showed promise. We called Paul at Mercury Magnetics and ordered a black-face Pro Tone Clone replacement trans-former, shut it down and wished each other a good holiday. A week later the Mercury Magnetics replacement output transformer had arrived. Jeff wired it up, and then turned his attention o three silver mica caps that had replaced the original ceramic caps in the phase inverter and tone circuits. Jeff: “Somebody probably read an article about how these would bring the high end up, but I prefer the ceramics—always have. Besides the effect of the voltage from the old output transformer being low, these silver mica caps were contributing to that brittle tone we were hearing. They are the wrong value, and they changed the entire sound of the amp.” Jeff pulled all three silver mica caps and replaced them with the correct ceramic disc caps, and since an on/off switch had already been installed for the tremolo, we mounted the 25K mid range pot in the back panel hole for the extension speaker jack. With the Pro now thoroughly put right and the midrange pot added, Jeff hit a few chords, moved the EQ and volume settings around a bit in both channels, smiled and said, “That sounds really good. Yeah, that’s it.”
Back in our music room, the final step was to re-bias the Proat 34mA with an AmperexGZ34 rectifier and our last pair of vintage RCA black plate 6L6s, which in unused, new old stock condition have soared to $400/pair. The re-labeled Tube NOS Phillips JAN 6L6 WGBs we had tried sounded good—but the smooth warmth, exceptional musicality and deep harmonic content of the RCAs just can’t be beat, and it is a difference you can definitely hear. Smoke ’em if you got ’em….
We lit up the Pro with the ’63Fender Reverb unit and reverently smiled at the jaw-dropping tones pouring from the big Eminence Legend 15. Imagine the sound of a slightly kinder, warmer sounding 40 watt Super Reverb void of the sharp, penetrating treble presence that has sooften left our ears ringing for hours after a tumble with a blackface Super. The sound of the ’64 Pro is all Fender, with solid bass that doesn’t fall apart at high volume as the smaller blackface combos can,sweet, singing treble tones, and now… a mid range control that can gradually push the amp beyond its original, clear and liquid “scooped” mid range voice to an exceptionally thick, “mid-Atlantic” roar that unleashes heavy sustain and rich, musical distortion as only a Fender can. The Pro brilliantly complements every guitar we own, producing the essence of classic Stratocaster, Tele, P90 and humbucker tones with clarity, depth and lush fidelity that literally fills the room. Yes, there are different and equally worthy tones to be had from the British classics,but we have never heard a more beautiful sounding or versatile Fender amp—one that can range from crystalline, blackface clarity to the full burn of an early blonde Fender Bassman at much friendlier volume levels. The Pro can get plenty loud, but it’s a loud that doesn’t kill you in the style of a Showman, Twin or a Super Reverb.
The irony in this unexpected discovery has not escaped us,and perhaps the weight of it is now becoming clear to you, too. This project did not begin well, and we confess to experiencing some remorse when the Pro arrived with a few bad mods, weak and thin from the original output transformer going down, and generally just sounding very wrong. Our dismay was soon displaced by genuine enthusiasm; however, as we were reminded that this is indeed what the quest for tone is all about it. We’ve acquired absolutely bone stock amps in perfect working condition that just couldn’t tote the note, so why should we expect to buy a 44 year old amp that’s been played without it needing a little repair and restoration work? The end entirely justifies the means.
Having finally experienced the Pro’s singular, exceptional sound, we wondered what had caused it to be relegated to such obscurity among all the Fender black face amps. Like the Vibrasonic and Vibroverb, perhaps it was doomed by the presence of the single 15” speaker. Like the Pro, the blackface Vibroverb 1×15 was produced for less than a year, and with the introduction of the 2x12Pro Reverb in 1965, Fender would no longer produce a 1×15 combo until the introduction of the silver face Vibrosonic in 1972. Yet, the earlier 1×16 Pros had been Fender’s flagship amps during much of the tweed era, and in 1960 the 1×15 brown Pro ranked second only to the1x16 Vibrasonic in the Fender catalog. Somewhere along the way, the 1×15 combo had clearly fallen out of favor with Fender, guitarists, or both, and given the short life span of the Vibroverb, even the addition of reverb couldn’t save it.
Twenty years later, Stevie Ray Vaughan elevated the Vibroverb to hall of fame status, otherwise, the 1×15 com-bos seem to have been perceived as “uncool” for anything bug jazz and blues, as if wearing a jacket and tie were required to play them. The Pro is a great blues amp, but it’s also a great rocker, and equally well-suited for jazz, pop and country. With far more clean head room and power than any tweed Pro and much stronger distortion, sustain and dynamic character than a brown Pro, the blackface Pro reflects Fender’s ongoing pursuit of more powerful, cleaner sounding amps, but unlike the black face Bandmaster, Tremolux and Showman, and Pro can really rock the house cranked. We suspect it’s a single 15 and missing ’verb that throws people off today, yet in’64 Pro shares its DNA with the ’64 Bassman and all the highly prized blackface combo amps, including the Deluxe Reverb, Vibrolux Reverb, Super Reverb and the heavily prized and hyped Vibroverb.
The contrast between the Vibroverb’s Holy Grail status versus the lowly blackface Pro simply underscores how easily we can be blown off course by what isn’t hyped on the Internet or in print, and by the powerful logic that suggests if anything 44 years old is truly noteworthy, “we” would already know about it. Well, apparently “they” don’t. But you do. Blackface Pros can be found for $1 500–$2,000,with originality and overall condition driving prices accordingly. Like the Deluxe, we wouldn’t buy one that has had all the blue molded capacitors or Allen-Bradley resistors replaced, but the transformers available today from Mercury will sound every bit as good or better than the originals, and as we have said so many times in the past,the Eminence Legend 15 is spectacular. Add some good,current production or NOS tubes and you will have been delivered to a place well beyond the common man’s limp and shriveled imagination. Now Quest forth….
Ten years after our first published amp review (the blackface Vibrolux Reverb), we still find ourselves answering readers’ questions about which amp to buy. We’re not complaining… your subscription to TQR has always included phone or email access for those contemplating a new gear purchase, but it seems that published reviews can still sometimes prompt more questions than answers. We understand, and like you, we are routinely faced with these same buying decisions just about every month as we look ahead to future issues. “Power” and “headroom” (or lack of it) seem to remain among the most daunting considerations for prospective amp buyers. This may not keep you up at night if you’re looking for a toneful box to play solely at home, but the range of clean and overdriven tones available from a single amplifier that can hang with a band is absolutely critical – the tipping point for guitarists who wish to have both clean and grittier tones available on the fly. And even the casual “bedroom” player (does anyone really play their guitars in the bedroom?) will quickly discover that big, lush guitar tones – clean or jacked into rich distortion – are often best obtained through a “bigger” amp. We’re not suggesting that we don’t love our ’58 tweed Tremolux or ’64 Deluxe – they both uniquely, timelessly epitomize great guitar tones – but an entirely different realm exists within the range of vintage Fender amps, and try as we might, we have never found another amplifier quite as versatile, user-friendly or uniquely toneful as the blackface (1965–7) 40 watt Pro Reverb – still the most under-valued and overlooked reverb amp from the entire blackface era, although aside from its 2×12 speaker configuration, the Pro is nearly identical to the Vibrolux and the Super Reverb amps.
Yes, the 2×12 Pro Reverb can move some air, just as an AC30or Matchless DC30, both highly coveted amps for good reason, do the same. Experienced in a room, 2×12 amps produce an ambient presence and a spatial quality that single 12s can’t match. That extra speaker isn’t adding volume as much as it simply disperse sound effectively by filling more space. And although the Pro Reverb is rated at 40 watts, the smaller output transformer Leo Fender chose to use delivers only 28 watts, probably in an effort to minimize speaker failure, yet the original Oxford and Jensen 12 s shipped in the Pro still blew when pushed by enthusiastic rockers. A well-maintained Pro Reverb will typically produce classically clean Fender tones with strong bass and treble and slightly diminished mids from “2” on the volume control to “5,” gradually spilling into lush Fendery distortion at higher settings. If you choose to use an overdrive device to achieve distortion at lower volume levels, the Pro will sound significantly better than most 20 watt amps because your pedal is affecting a cleaner signal, rather than adding distortion to an amp already spilling over into distortion. And as we have reported so often in the past, non-invasive and completely reversible modifications can be made, such as the addition of a 25K mid range pot utilizing the existing back panel hole for the extension speaker jack. This single mod enables the Pro to develop a very ballsy British voice as midrange is increased, while completely preserving the integrity of the original Fullerton tone with the midrange pot set at zero, rendering two outstanding amps in one. Intrigued? You should be, because we have never heard a contemporary boutique 2×12 combo amp that can approach the sound of a Pro Reverb equipped with a solid set of tubes and speakers. And with the range of speaker options available today, you can effectively custom design and shape the sound of your Pro for more of a traditional, bright“American” sound, a heavier or chimier British tone, or the two combined.
Ah, but buying old amps is risky business says you… what if I get a “dog” or it needs a lot of work? I’d rather buy some-thing new and not deal with the unknown. Fine, do that. But for those willing to reap the rewards that only a certain degree of risk can offer, it’s not that difficult to minimize your chances for disappointment. Here’s how:
It only stands to reason that a guy whose day gig involves running his own successful and renowned pickup company knows killer tone when he hears it. So when the Jones hit to seek out a custom made map that combined the best of his favorite Blackface Vibroverb and Vibrolux, Lindy Franlin called upon Tony Albany and the guys at Vintage Vacuum Tube Amps to see if they might be up to the task. And that they were.
The holy grail would be to produce a 6L6 based 30 watt tone machine capable of a beautiful clean sound as well as a smooth, crunchy overdrive and be put captive into the smallest and lightest workable cabinet.
Beginning with a 2×10 Mojotone Tweed Super amp kit for the basic prototype, VVT and Fralin tweaked their hearts out for six months until they got it right.
Residing in a rather compact 20×20 cabinet, the VVT Lindy Fralin Model strikes a vintage pose in its white Tolex with oxblood-like grill cloth.
Beginning with a 2×10 Mojo tone Tweed Super amp kit for the basic prototype, VVT and Fralin tweaked their hearts out for six months until they got it right. Residing in a rather compact 20×20 cabinet, the VVT Lindy Fralin Model strikes a vintage pose in its white Tolex with oxblood-like grill cloth.
The VVT Lindy Fralin Model is a cathode biased straight forward, no bells and whistles affair. The “Plexi”top panel is simple and clean with its Input, bright switch, volume, treble and bass controls followed by the reverb control, standby and on/off switch. Chicken-headknobs let you know where you’re at. Two TAD matched 6L6 tubes supply the power with two 12AX7s for the preamp. A pair of 12AT7s are for the reverb driver and phase inverter. Rectifyin’ is courtesy of an Electro Harmonix 5U4GE. The cool thing is that the Lindy Fralin Model can also accept a deuce of 6V6s in place of the big bottles in the power section for a whole different vibe. Because of the higher plate voltages, VVT Amps stresses that only modern tubes (like the supplied JJ Electronics) should be used. You don’t want to blow the thing up, do ya?
If you think a 15 inch speaker might get as loose and floppy as your Auntie Mabel’s arse, you might be in fora pleasant surprise. With an obviously wider bass frequency range than a 12 inch, the Weber’sbottom remains tight and punchy with a nice lower mid section as well.Single coil and humbucker equipped instruments alike snuggled up quite admirably to the Weber Classic.
First impressions? The Lindy Fralin Model with my Strat spoke with gorgeous single coil chime and harmon-ic complexity, unabashedly magnified with a full trans-parent tone and organic beefy sustain. Very articulate and touch sensitive, the amp displays a more than impressive amount of projection. Both Lindy and Tony attribute this to the cross shaped members (called an integral diffuser) placed across the speaker opening in the baffle board which help disperse the sound and tame some of the“beamy” high end.
All tone controls are unobtrusive and very musical. While the treble is subtle up to around 6 on the dial, the bass is more evident from the get go but remains trans-parent throughout its range with no muddiness. The bright switch surrounds the notes and chards alike with an airiness without compromising the inherent full tone of the amp.
In addition to the Strat, the Lindy Fralin Model warmed up nicely to my other 6 string friends. The Carvin California Carved Top sounded sweet and detailed while my Ibanez AS200spoke with a very articulate, full and warm bodied tone.
Arch tops? This little box makes a nice jazz amp as well with clear, well defined chord structures and beefy single notes. With the fat axes pushing the volume past 3-1/2 caused a little mush in the low end which could probably be remedied by changing the first preamp tube to something with a bit less gain.
The reverb fills out the sound with a pleasant mix behind the dry signal. Throughout its range, the effect is very complimentary and doesn’t send your playing out to see even when dimed. For the dirty stuff, cranking the chicken head to the red(!) produced a bubbly, organic and throaty overdrive with real honest to goodness preamp/amp interaction. Very sweet with gobs of sustain. Doing a quick swap to the matched pair of 6V6s morphed the amp into a kind of Blackface Deluxe vibe with breakup noticeable at lower levels. The bottom felt a little less tight with a bit more perceived glassiness in the top end.
Whereas the 6L6 bottles speak “tux and bow tie” the6V6s are more “t-shirt and jeans”—not quite as complex but with a grittier and nice fat tone.
Also VVT Amps’ attention to detail gets a big thumbs up for the extra long line cord and groovy little spare fuse holder inside the back of the amp.
The collaboration between VVT Amps and Lindy Fralin has turned out to be a winning combination. The VVT Lindy Fralin Model’s beautiful, three-dimensional tones are equaled only by its straight-forward and no-nonsense design.
Tweed — Universal Voltage Primary
Tweed — Universal Voltage Primary — lower B+
Tweed — #125P6A
Late ’50s Tweed — #50246 — 8 kΩ primary, single 8 ohm tap
Secondary has self leads like original — Horizontal frame — 3 1/8″ mounting centers
